Quantum effect of cooling down the environment temperature of mesoscopic LC circuit

We examine the quantum effect of cooling down the environment temperature of mesoscopic LC circuit, and find that the ground state of the circuit is no longer in the thermo vacuum state, but in a negative binomial state. We calculate energy of the circuit in this new state, which increases with the cooling of the environment.     

等温退火对8030铝合金导线组织性能的影响

研究了不同等温退火工艺对8030铝合金导线组织及性能的影响。结果表明:等温退火前后合金均由α-Al基体和Al₆Fe相组成。在同一等温温度下,随着等温时间的延长组织逐渐趋于均匀化;同一等温时间下,随着等温温度的升高,组织趋于均匀化的时间缩短。经过等温退火处理后铝合金导线的导电率均有所提高,在470 ℃均匀化退火24 h后再经240 ℃等温4 h,合金导电率达到最高值57.21%IACS,比未经热处理试样的导电率提高了2.4%IACS。经过等温退火处理后铝合金导线的硬度及抗拉强度均有所降低,塑性大幅度提高。在470 ℃均匀化退火24 h后再经260 ℃等温8 h,合金的伸长率最高可达23.64%。热处理前后合金均为塑性断裂。     

以任意高维纠缠态为量子信道的受控隐形传态

目的是利用高维量子纠缠态为量子信道，讨论未知单粒子态的受控隐形传输问题。以三维量子纠缠态为信道，提出一个二维任意单粒子态的受控隐形传输协议。提出了以任意[d]-维量子纠缠态为量子信道，[t]-维任意单粒子态的隐形传输协议[(t相似文献   

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.     

Polynomial filtering for nonlinear stochastic systems with state‐ and disturbance‐dependent noises

This article is concerned with the polynomial filtering problem for a class of nonlinear stochastic systems governed by the Itô differential equation. The system under investigation involves polynomial nonlinearities, unknown‐but‐bounded disturbances, and state‐ and disturbance‐dependent noises ((x,d)‐dependent noises for short). By expanding the polynomial nonlinear functions in Taylor series around the state estimate, a new polynomial filter design method is developed with hope to reduce the conservatism of the existing results. In virtue of stochastic analysis and inequality technique, sufficient conditions in terms of parameter‐dependent linear matrix inequalities (PDLMIs) are derived to guarantee that the estimation error system is input‐to‐state stable in probability. Moreover, the desired polynomial matrix can be obtained by solving the PDLMIs via the sum‐of‐squares approach. The effectiveness and applicability of the proposed method are illustrated by two numerical examples with one concerning the permanent magnet synchronous motor.     

An improved iterative stochastic multi-objective acceptability analysis method for robust alternative selection in new product development

Alternative selection in new product development (NPD) is a multi-criteria decision-making (MCDM) problem. It usually starts with incomplete, imprecise or even partially missing information. Currently, most existing methods in dealing with this problem cannot work well if required information is incomplete or missing. It is acknowledged that stochastic multi-objective acceptability analysis (SMAA) can be applied to address MCDM problem with incomplete preference information and uncertain criteria measurements. In SMAA, alternatives are evaluated based on SMAA measurements (acceptability index, central weight vector and confidence factor). The discriminability of SMAA for the optimum alternative heavily depends on differences of SMAA measurements among different alternatives. Usually, a large number of alternatives and high level of uncertainty are involved in alternative selection in NPD. In this situation, the differences among SMAA measurements are not obvious, and therefore SMAA cannot deal with such problem very well. To this end, this paper proposes an improved SMAA method called Iterative-SMAA (I-SMAA) for alternative selection in NPD. In the I-SMAA, an iterative multi-step decision-making process is suggested to improve differences of SMAA measurements among different alternatives, and thus assist decision makers (DMs) to positively discern from the most preferred alternative. To enhance the decision-making efficiency, sensitive criteria are acquired in each iteration by ranking sensitivity analysis. DMs are guided to provide partial preference information and give more accurate criteria measurements for sensitive criteria rather than all criteria. Eventually, to verify the proposed method, a numerical example of the existing literature is solved with the method, and the results are compared. And then, a practical example of a preparation equipment for coal samples is further employed to verify the practicability of the proposed I-SMAA.     

Analyzing dissipation effects on the non-classicality witnessing by a qubit via the entangled state representation

ABSTRACT

In this paper, we study detection of the state non-classicality for a quantum harmonic oscillator by a qubit in the presence of dissipation effects. We show that dissipation can enhance the effectiveness of the method in case of using the corrected form of the related nonclassicality witness. Such an improvement is attributed to the fact that dissipation leads to probing a surface, instead of a curve, of the complex plane for non-classicality condition on normally-ordered characteristic function.     

低活化马氏体钢热变形行为及机理型本构建模研究

利用Gleeble-3500热模拟试验机研究了低活化马氏体钢在变形温度为850～950 ℃、应变速率为0.001～1 s^-1条件下的热变形行为。建立了流变应力本构方程，并评估了该方程的预测能力。绘制了低活化马氏体钢在不同应变下的热加工图。结果表明：在较高的应变速率条件下，该材料主要发生动态回复，在较高变形温度和较低应变速率下具有明显的动态再结晶特征；本构方程的预测结果与实验结果符合良好；变形温度870～930 ℃、应变速率0.001～0.01 s^-1和变形温度920～950 ℃、应变速率0.3～1 s^-1分别是真应变为0.4和0.6下最优的热加工区域。